← Back to Home

Logic Analyzer Specs: The 16-Channel Sample Rate Cliff

logic analyzersample rateusb bandwidth

Search for a logic analyzer and the product title will lead with a big sample rate: 400 MS/s, 500 MS/s, 1 GHz. Buy it, clip sixteen wires to your board, and the number in the software quietly drops — to 100 MHz, or to 20 MHz.

That is not false advertising. The vendor put the full derating table in the datasheet; the listing copied one cell of it. I pulled the DreamSourceLab datasheets and the Kingst selection table, wrote the multiplications out row by row, and found every tier obeys the same ceiling. That ceiling is the interface bandwidth itself.

Every spec number here comes from vendor PDFs and the official product tables, retrieved 2026-11-03. Prices are what the Amazon page showed that day. The Amazon links below are affiliate links — I earn a commission if you buy through them, and your price does not change.

TL;DR: 400 MS/s is a few-channel number. With all 16 channels enabled, the vendor's own table says 100 MS/s in buffered mode, or 20 MS/s in streaming mode. Three things you can use right away: ① channels multiplied by per-channel rate is a constant — USB 2.0 units land at 256–320 M samples/s, USB 3.0 units at 2000–3000 M, and buffered units at 1600 M (DSLogic Plus) or 8000 M (U3Pro16); ② buffered capture is short, 0.16–0.31 seconds with 16 channels; ③ the cheap 24 MHz units only belong on signals below about 20 MHz. Buying today: DSLogic Plus at $149 for slow buses, LA5016 at $299 for 500 MS/s on all channels, DSLogic U3Pro16 at $299 for USB 3.0 streaming.

Three vendor tables, one rule

Start with the DSLogic Plus. Its datasheet (v1.2, revised 2020-06-20) splits maximum sample rate into two columns, buffered and streaming:

ChannelsBuffered modeStreaming modeProduct (M samples/s)
3not supported100 MHz300
4400 MHznot supported1600
6not supported50 MHz300
8200 MHznot supported1600
12not supported25 MHz300
16100 MHz20 MHz320

The right column is channels times per-channel rate. All four streaming tiers land between 300 and 320. All three buffered tiers are exactly 1600.

Now the U3Pro16 (datasheet v1.1, 2020-02-20). Streaming: 1 GHz on 3 channels, 500 MHz on 6, 250 MHz on 12, 125 MHz on 16 — products of 3000, 3000, 3000, 2000. Buffered: 1 GHz on 8 channels, 500 MHz on 16, both 8000.

The third table is Kingst's official product selection chart, which packs the tiers into a single cell: the LA1010 reads "100M@3CH, 50M@6CH, 32M@9CH, 16M@16CH", giving 300, 300, 288, 256. The same table lists the LA2016 at 200M@16CH (3200) and the LA5016 at 500M@16CH (8000).

Three tables, five instruments, a dozen combinations, and the products only land on four values: 256–320, 1600, 3000, 8000. That is not a coincidence. Those are four different physical limits — USB 2.0 bandwidth, memory bandwidth inside a USB 2.0 unit, USB 3.0 bandwidth, memory bandwidth inside a USB 3.0 unit.

Where the 60% comes from

USB 2.0 Hi-Speed signalling runs at 480 Mbit/s. Each channel spends one bit per sample, so 300 M samples/s is 300 Mbit/s on the wire — 62.5% of 480. The 16-channel tier at 320 is 66.7%.

The vendor says so out loud. The DSLogic product page states that real-time transfer is limited by USB bandwidth and that "Only 3 channels support under 100M sample rate", then notes that U3Pro units add a super stream mode over USB 3.0 with "bandwidth up to 5Gbps" — "10 times than normal stream mode".

That claim is checkable. 3000 ÷ 300 = 10.0, exactly ten. The tiers were not chosen by feel; the interface was fixed first, then the per-channel rate was solved backwards from the channel count.

Push the same logic further. A USB 2.0 host delivers roughly sixty percent of the signalling rate in practice, and it does not go higher. So when a USB 2.0 analyzer advertises "16 channels at 100 MS/s real time", do the multiplication — 16 × 100 = 1600 Mbit/s, more than three times 480. It cannot physically stream that. Something shrank: the rate drops to 20 MHz at 16 channels, or only three channels are active, or the samples go into onboard memory.

I worked the same bandwidth arithmetic in the 4K webcam USB bandwidth piece; cameras count pixels, analyzers count bits, the constraint is identical.

Buffered mode: what 0.16 seconds buys you

If real-time streaming cannot keep up, store samples on the board first and transfer afterwards. That is buffered mode, and the headline sample rate on every listing refers to it.

The question is how much memory. DSLogic Plus has 256 Mbit, the U3Pro16 has 2 Gbit, Kingst's LA2016 has 1 Gbit, the LA5016 has 2 Gbit. The datasheet line that matters: "Buffer mode (without RLE compression): 256M / num. of channels" — memory is divided among active channels.

So capture length is a fixed value:

ModelMemoryRate at 16 channelsPer-channel storageCapture time
DSLogic Plus256 Mbit100 MHz16 M samples160 ms
DSLogic U3Pro162 Gbit500 MHz125 M samples250 ms
Kingst LA20161 Gbit200 MHz62.5 M samples313 ms
Kingst LA50162 Gbit500 MHz125 M samples250 ms

Look at the DSLogic Plus row: 400 MHz on 4 channels, 200 MHz on 8, 100 MHz on 16 — and all three configurations produce 160 milliseconds. Because memory is split by channel, the number of channels changes how fast each one runs, not how long you can record.

160 to 313 milliseconds, all under a third of a second. That is the real capacity of buffered mode: it is not for watching a bus, it is for catching the waveform around a trigger. To watch a bus for minutes you have to fall back to streaming, and streaming is capped at that 300 M samples/s.

Compression ratios are numbers nobody guarantees

Both datasheets mention RLE compression raising depth: DSLogic Plus from 256 Mbit to 16 Gbit (62.5×), U3Pro16 from 2 Gbit to 16 Gbit (8×).

The catch is that the ratio depends on the signal. An idle bus with a clock that rarely toggles compresses brutally well; once data lines start switching every sample, the ratio collapses. Kingst names that row honestly in its own table: "Max Compression Depth (can't be ensured)" — the vendor will not stand behind the compressed figure.

So 16G is a best-case ceiling, not your working capacity. Budget against the uncompressed 256 Mbit and 2 Gbit, which are the parts that can be promised.

Sample rate, fastest signal, minimum pulse width

Kingst puts three easily-confused numbers on one row. LA1010: max sample rate 100M@3CH, fastest digital signal 20 MHz, minimum pulse width 20 ns.

Sample rate divided by fastest signal is 5×. DreamSourceLab's product page advises that "sample rate should be 10x – 100x than frequency of under test signal". Two vendors, and the multiplier differs by a factor of two to twenty.

Neither is wrong; they answer different questions. Five times means "you can see that this frequency exists". Ten times and up means "you can trust the duty cycle and edge position". For I²C at 400 kHz or UART at 115200, anything works. For a 50 MHz SPI clock, the 10× rule wants 500 MS/s while Kingst's 5× rule is satisfied at 250 MS/s — and that gap decides whether you spend twice as much.

My own approach is to work backwards from the shortest pulse. A 50 MHz SPI clock has a 10 ns high phase, so the sampling interval has to be well under 10 ns: 100 MS/s at the floor, 200 MS/s to be comfortable. That calculation needs no vendor convention at all.

Five instruments, one decision order

Sort by the fastest signal you actually need to capture, then by channel count, and only then look at the headline number.

Slow buses on a budget: HiLetgo 8-channel 24 MHz ($12.69)

The listing says 24 MHz and 8 channels, a product of 192 M samples/s — well inside the USB 2.0 ceiling. UART, I²C and slow SPI with PulseView is a working combination. The listing is HiLetgo 24MHz 8CH.

Real drawback: the listing gives nothing beyond "24MHz 8CH" — no threshold range, no memory size, no interface generation, no datasheet. A fixed threshold means 1.8 V logic reads unreliably. And 24 MHz sampling under the 10× rule only covers signals up to 2.4 MHz, far below what most buyers assume.

The 16-channel, 100 MHz tier: LA1010 ($69)

Kingst lists the same model at $68, with the full table: 100M@3CH, 50M@6CH, 32M@9CH, 16M@16CH, fastest digital signal 20 MHz, minimum pulse width 20 ns, no hardware memory. The Amazon page is LA1010 16 channels.

Real drawback: with all 16 channels enabled you get 16 MHz — the "100MHz" label shrinks by 6.25× at full width. No onboard memory means everything depends on real-time transfer, so your host USB port directly limits whether it reaches spec. The table does not state the interface generation, but a 300 M samples/s product only makes sense as USB 2.0.

400 MHz and 16 channels: DSLogic Plus ($149)

$149 on the vendor site (list $199), the same on Amazon. 256 Mbit buffered, 16 channels at 100 MHz, 8 at 200 MHz, 4 at 400 MHz. Adjustable threshold in 0.1 V steps, and the datasheet states support from 5 V down to 1.0 V logic — which is what 1.8 V MCUs need. Buy page: DSLogic Plus.

Real drawback: USB 2.0, so streaming tops out at 20 MHz on 16 channels, and buffered capture at 16 channels is 160 ms. The "System Requirements" section still lists Windows XP through Windows 10; the document stopped at 2020, so check the vendor site for current OS support.

500 MS/s on all 16 channels: Kingst LA5016 ($299)

Selection table: 500M@16CH, 2 Gbit hardware memory, fastest digital signal 80 MHz, minimum pulse width 6.25 ns. Sixteen channels at 500 MS/s is 8000 M samples/s of internal throughput, which only onboard memory can absorb. The listing is LA5016 16-channel 500MS/s.

Real drawback: $299 is the Amazon price while Kingst's own site lists the same model at $238 — 25.6% more (see below). At full width, 2 Gbit of memory is 250 ms. The selection table does not name the interface type; the throughput numbers only work as buffered capture with a transfer afterwards, so do not expect to watch live at that rate.

Long streaming over USB 3.0: DSLogic U3Pro16 ($299)

$299 on the vendor site (list $399), the same on Amazon. Streaming runs 1 GHz on 3 channels and 125 MHz on 16, products of 2000–3000 — ten times the USB 2.0 class. Buffered, 2 Gbit of DDR3 gives 1 GHz on 8 channels and 500 MHz on 16, with 0.1 V threshold steps and a 2 ns minimum pulse. Buy page: DSLogic U3Pro16.

Real drawback: 1 GHz only exists at eight channels or fewer; sixteen drops it to 500 MHz and streaming drops it again to 125 MHz. USB 3.0 is a hard requirement — plug it into a USB 2.0 port and the advantage disappears. The vendor's own note that it "can be used to capture up to 250MHz digital signals (under 1G sample rate)" says the probes and wiring are the real bottleneck, and the sample rate is only a paper condition.

Check the vendor price before you check out

The gap between Amazon and the official store is not consistent. DSLogic Plus: $149 both places. U3Pro16: $299 both. LA1010: $68 official, $69 on Amazon. LA5016: $238 official, $299 on Amazon — a $61 difference.

The largest gap sits on the mid-tier unit. If the vendor ships to you, or if 25.6% matters, verify the price on the manufacturer's store first. Conversely, both DreamSourceLab units cost the same either way, and Amazon's shipping and returns are easier to deal with.

Prices move. These are the values shown on 2026-11-03; check the page before ordering.

FAQ

Q: The listing says 400 MS/s, so why does the software show 100 MHz?

A: 400 MS/s is the four-channel figure. The datasheet derating table gives 200 MHz at eight channels and 100 MHz at sixteen. The software reports the ceiling for your current channel configuration, not the headline cell.

Q: Should I use streaming or buffered mode day to day?

A: Streaming for watching a bus over time, at the cost of a rate capped by USB bandwidth. Buffered for fast transients, at the cost of 0.16–0.31 seconds of capture. You cannot have both at once.

Q: Is more channels always better?

A: No. Memory is divided by channel, so running sixteen channels gives each one a sixteenth of the storage, and the rate table drops too. If you only decode I²C and UART, an 8-channel unit can actually run faster.

Q: Can a cheap 24 MHz unit decode SPI?

A: Under the 10× rule, 24 MHz sampling covers signals to about 2.4 MHz. SPI clocks usually sit between a few MHz and tens of MHz, so slow modes are marginal and edge positions will not be trustworthy. Timing measurements need 100 MS/s and up.

Q: Why is the vendor's "fastest signal" so much lower than the sample rate?

A: Sample rate is the converter's speed. Fastest signal is what the whole chain — probe, wiring, shielding, threshold — can deliver without distortion. Kingst states a 5× relationship, DreamSourceLab recommends 10× to 100×. The conservative number is the one your measurements will actually match.

Q: Does a logic analyzer need calibration?

A: It only decides high or low, it does not measure absolute voltage, so it does not need the amplitude calibration an oscilloscope does. Threshold setting does change the answer, though, and 1.8 V logic needs an adjustable threshold. For bandwidth conventions on the analog side, see this 100 MHz oscilloscope guide; the error sources are different. If what you need is supply-side current and protocol data, a USB power meter is the direct route.

Scope and data notes

All spec figures come from DreamSourceLab's DSLogic Plus and U3Pro16 datasheets and Kingst's official selection table, retrieved 2026-11-03, without second-hand retelling. The 480 Mbit/s and 5 Gbit/s figures are USB-IF specification values. The "constant product" conclusion is my own derivation: I actually multiplied the official rows one by one, and no vendor states it that way. DSLogic's own claim of "10 times than normal stream mode" matches 3000 ÷ 300 = 10.0 exactly, which cross-checks it.

What I did not do: I have not put these instruments on a scope to measure eye diagrams or jitter, and I have not verified RLE compression ratios on a real bus. Every capture-time figure is computed from official memory capacity and the derated sample rates, so real numbers will shift with trigger settings and signal activity. Prices are what the pages showed at retrieval time and will change.

If you decode I²C a few times a year, the $12.69 unit is enough. If debugging is the day job, the $149 to $299 range buys the absence of waiting — no waiting for a capture to finish, and no cutting the rate to 20 MHz to keep sixteen channels. What you pay for there is time, not accuracy.

👉 Join Xiaomi MiMo Platform: Leading AI model platform with cost-effective inference

👉 Join Aliyun AI: Top AI products with exclusive coupons for business innovation

📌 This article was AI-assisted generated and human-reviewed | TechPassive — An AI-driven content testing site focused on real tool reviews

🔗 Recommended Tools

These are carefully selected tools. Using our affiliate links supports us to keep producing quality content:

As an Amazon Associate, I earn from qualifying purchases at no extra cost to you.

☁️ DigitalOcean Cloud ⚡ Vultr VPS 🤖 QoderWork CN (Refer & Earn) ☁️ Aliyun AI Products 📚 WordPress Books 🧠 AI & LLM Books 🏗️ System Design Books 🐳 Docker & K8s Books 🐧 Linux Admin Books 🐍 Python Books 🗄️ Database Books 🚀 DevOps & SRE Books 🤖 Xiaomi MiMo Platform
← Back to Home