Laser engravers: what 40W and Class 1 really mean
I cleared an old inkjet off my desk last month and started shopping for a desktop laser engraver to fill the space. Two weeks of spec sheets later, one pattern held across every brand: the biggest number on the listing is rarely what it appears to be.
The same machine will advertise 40W while its own module page says eight 5.5W lasers are combined into 40W. A brand's 20W model can offer a larger work area than its 40W model. Two 40W machines sit on opposite ends of the safety scale, one Class 1 and one Class 4. All three point at the same question: under what conditions does that number hold.
This is not a benchmark. I pulled the official spec sheets for four machines sold on amazon.com and put them side by side. Prices below are the brands' own published prices as of writing; live Amazon pricing and stock change and should be checked on the product page, because the network I fetch from does not return those fields.
This article contains Amazon affiliate links. If you buy through them I earn a commission, at no extra cost to you, and it does not change which flaws I write about here.
Where the four machines sit
TL;DR: On a tight budget, AtomStack Swift (7W/12W, 300 × 300 mm, $269 list). For a 20W mid-tier, AtomStack A20 Pro V2 (400 × 365 mm, $530). If you want the same power with faster travel, Ortur Laser Master 3 (20W, 20,000 mm/min, from $599.99). If the machine has to be Class 1 because it lives in a house with kids or pets, Ortur H20 (enclosed, 10/20/40W modules, from $1,179).
- AtomStack Swift: the smallest footprint here. Two versions, 7W and 12W, cutting 4 mm and 7 mm of basswood plywood in a single pass. Listing: AtomStack Swift laser engraver.
- AtomStack A20 Pro V2: single 20W module, official ceiling of 17 mm on wood, 120W input. Listing: AtomStack A20 Pro V2.
- Ortur Laser Master 3: 20W module with a square 0.08 × 0.08 mm spot and 20,000 mm/min travel. Listing: Ortur Laser Master 3.
- Ortur H20: enclosed, Class 1, with 2W infrared, 10W, 20W and 40W modules. Listing: Ortur H20 enclosed laser engraver.
That 40W is several diodes summed together
xTool states it plainly on the S1 40W module page: "eight 5.5W lasers are combined into 40W". Eight diodes, optically compressed onto one spot, usually with FAC-type beam shaping. That is how diode machines reach the 40W class at all.
What this means in practice: the 40W you are buying is the sum of eight emitters, not one emitter. A single 5.5W diode and a single 40W diode are different processes with different yields and different costs. When you see a 40W badge, look for the "×5.5W" or "×10W" breakdown on the module page. If the brand does not publish it, that is itself information.
The second misread is electrical. Rated power is optical output; the wall socket sees something else.
| Machine | Optical output | Official supply figure | Wall draw |
|---|---|---|---|
| xTool S1 40W | 40W | 25V 11A output | about 275W |
| Creality Falcon2 40W | 40W | 240W machine power max | 240W |
| AtomStack A20 Pro V2 | 20W | 120W input | 120W |
| AtomStack Swift | 7W / 12W | not stated in one place | check the manual |
Budget 240–275W of headroom on the strip for a 40W-class machine, not 40W. Run it all evening and that difference shows up as heat in the wiring.
Spot area is the number that decides
Power divided by spot area is the intensity actually landing on the material. Every figure below comes from a manufacturer's own sheet.
| Machine | Rated power | Official spot (mm) | Area (mm²) | Geometric density (W/mm²) |
|---|---|---|---|---|
| AtomStack Swift 12W | 12W | 0.08 × 0.04 | 0.0032 | 3,750 |
| Ortur Laser Master 3 20W | 20W | 0.08 × 0.08 | 0.0064 | 3,125 |
| AtomStack A20 Pro V2 20W | 20W | 0.08 × 0.10 | 0.0080 | 2,500 |
| xTool S1 20W | 20W | 0.08 × 0.06 | 0.0048 | 4,167 |
| xTool S1 40W | 40W | 0.08 × 0.10 | 0.0080 | 5,000 |
| Creality Falcon2 12W | 12W | 0.06 × 0.08 | 0.0048 | 2,500 |
| Creality Falcon2 40W | 40W | 0.08 × 0.12 | 0.0096 | 4,167 |
Two results run against intuition.
First: the AtomStack A20 Pro V2 at 20W and the Creality Falcon2 at 12W land on exactly the same 2,500 W/mm². Power rose 67 percent, spot area rose 67 percent, and intensity did not move. The 20W machine covers more ground per hour because it delivers more total energy, but the ability to burn through a given layer still follows density.
Second: going from xTool's 20W module to its 40W module doubles power but lifts density by 20 percent (4,167 to 5,000), because one axis of the spot grows from 0.06 mm to 0.10 mm.
Three caveats, so this does not get treated as gospel. A rectangular spot is a geometric stand-in for a real energy distribution that is neither flat nor perfectly Gaussian. Manufacturer numbers are taken under favourable conditions, and a 0.5 mm focus error moves them. Brands also disagree on how to measure a spot at all, including whether the 1/e² edge counts. Within one brand's lineup the ratios hold up; across brands, treat them as a rough guide. It is the same lesson as our piece on diopter versus magnification in magnifier lamps: the loudest number on the listing is rarely the deciding one.
Why 17 mm and 10 mm describe the same 20W
AtomStack's spec table for the A20 Pro V2 lists 17 mm as the maximum wood thickness. xTool's official comparison page gives its 20W S1 module 10 mm of cherry in a single pass. Both are the manufacturers' own numbers, and they differ by 70 percent.
Nobody is lying. The test conditions differ:
- Different material. Cherry and basswood are not the same density, so the same power cuts different depths.
- Different speed and pass count. "One pass" is paired with a speed that usually does not appear in the headline. Slow the head down and the same machine goes deeper.
- Different definition of cut. Falling apart when you push it is not the same result as a clean edge with no char.
AtomStack's own wiki is explicit for the Swift: 4 mm basswood at 7W, 7 mm at 12W, both at 100 percent power. The number holds only at full power, on a named material, in one pass.
Compare like with like, or remember that maximum cut depth is a demonstration, not a production rate. Cutting 3 mm plywood for jigs leaves all four machines with margin. Cutting 15 mm solid stock is out of reach for the machine rated at 7 mm, no matter how you tune it.
Class 1 and Class 4 differ in the enclosure
Creality's spec table for the Falcon2 40W reads "Safety Class: Class 4 (FDA)". xTool lists "Class 1 Safety" for the S1 alongside five-direction flame detection, an emergency stop, a lid-open stop and a key lock. Ortur lists "Class 1 Laser" for the H20 with a lid safety lock and nine protection layers.
Two of those are 40W-class machines on opposite sides of the classification. The laser is not what changed. The enclosure and the interlocks are. Class 1 means that under normal use a person cannot be exposed to radiation above the limit, which forces a closed cabinet, a lid that kills the beam, and no stray optical path. Class 4 is an open beam, and the machine does nothing about it; containment becomes your job.
The A20 Pro V2 is a third case. Its official spec table gives no laser class at all, just a certification list: IEC 60825, CE, FCC, RoHS, FDA, PSE, UKCA. An open frame, a magnetic filter shield and blue-blocking goggles are the containment strategy. This is not a defect: an IEC 60825 certification of the laser product and a Class 1 rating of the assembled machine under defined conditions are different claims. What it does mean is that an open-frame buyer funds the enclosure, the goggles and the floor space, and those costs are routinely left out of the comparison.
AtomStack's wiki says the same thing about the Swift in its own words: an open-frame machine, so wear laser safety goggles and use an enclosure for smoke control.
The four machines, one at a time
AtomStack Swift: smallest footprint
| Spec | Official figure |
|---|---|
| Laser power | 7W or 12W |
| Work area | 300 × 300 mm |
| Spot | 0.08 × 0.04 mm |
| Max speed | 10,000 mm/min |
| Single-pass cut | 4 mm (7W) or 7 mm (12W) basswood at 100% power |
| Net weight | 2.8 kg |
| List price | $269 (12W) |
What you accept: 300 × 300 mm is the smallest bed here, so anything A3-sized gets tiled. The frame is open, so goggles and an enclosure are extra purchases. The official wiki advises against LaserGRBL because 460800 baud is not reliably supported, and Wi-Fi needs the beta AtomStack Studio, with a wired connection recommended. The same wiki says cutting metal is not recommended.
AtomStack A20 Pro V2: the 20W middle
| Spec | Official figure |
|---|---|
| Laser power | 20W (120W input) |
| Work area | 400 × 365 mm |
| Spot | 0.08 × 0.10 mm |
| Max speed | 400 mm/s |
| Official ceilings | wood 17 mm, acrylic 15 mm, leather 2 mm |
| Net weight | 6 kg |
| List price | $530 |
What you accept: the same page carries two accuracy figures, "0.01mm engraving accuracy" in the marketing block and "Engraving Accuracy: 0.02mm" in the spec table; trust the table. Flame detection needs the Z2 Z-axis slider. Focus is manual and there is no camera, so registration is by crosshair. No laser class is published, so containment is on you. A 6 kg frame machine moving at 400 mm/s will show every wobble in your bench.
Ortur Laser Master 3: same power, more speed
| Spec | Official figure |
|---|---|
| Laser power | 20W module (LU3-20A) |
| Spot | 0.08 × 0.08 mm, square |
| Max speed | 20,000 mm/min |
| 20W bundle | Ortur Air Pump 1.0 included |
| List price | $599.99 (regular $999.99) |
What you accept: the square spot is the selling point, quoted by Ortur as 256 grey levels, but 0.08 × 0.08 mm puts geometric density at 3,125 W/mm², above the equally rated A20 Pro V2 and below the 12W Swift, squarely in the middle. 20,000 mm/min is unloaded travel; cutting speed is an order of magnitude lower. The fact that the air pump is bundled with the 20W version tells you the bare configuration cuts dirtier. And Ortur's own H20 FAQ states that H20 modules are not compatible with other Ortur models, so the two lines do not share consumables.
Ortur H20: enclosed, with an area penalty
| Spec | Official figure |
|---|---|
| Laser power | 2W IR / 10W / 20W / 40W modules |
| Work area | 10W and 20W: 420 × 300 mm; 40W: 410 × 275 mm |
| Max speed | 20,000 mm/min |
| Focus | autofocus on 40W, manual on 2W/10W/20W |
| Laser class | Class 1 |
| Weight | 21.62 kg with the 40W module |
| List price | $1,179 (regular $1,499); €1,259 in Europe |
What you accept: this is the detail worth remembering. Stepping up to the 40W module shrinks the work area from 420 × 300 mm to 410 × 275 mm. Ortur's comparison table lists it row by row; it is not a typo. A higher-power module is physically larger and eats travel. Second, autofocus exists only on the 40W module; the other three are manual. Third, 21.62 kg is no longer a carry-it-to-the-table weight. Fourth, Ortur's own FAQ says ventilation is still recommended even with the enclosure.
Three costs that come with any of them
Extraction. All four need it, enclosed or not. A window is the cheap route. Without one you add a purifier, and that box is frequently as bulky as the machine. Air handling around a bench is its own subject; our piece on ultrasonic cleaner power density and load ratio works the same "rated versus usable window" problem.
Test stock. Settings are not looked up, they are cut. The same basswood at a different moisture content or from a different batch wants different power and speed. Twenty identical test blanks will do more for you than a second module.
Software. LightBurn is paid; vendor apps are free and narrower. Most open-frame machines talk to LightBurn directly, while some enclosed models need the vendor app before the camera and autofocus work. Confirm your software is on the compatibility list before you buy.
Frequently asked questions
Q: Can a 20W machine cut 10 mm basswood?
It depends on speed and passes. The 10 mm in a single-pass claim is paired with a slow speed; slow it further or add a second pass and a 20W head will go deeper. What usually stops you is char and edge squareness, not power.
Q: Does an enclosure mean I can ignore the smoke?
No. Ortur's own H20 FAQ still recommends ventilation. The enclosure controls beam exposure and lid interlocks; smoke still needs a duct or a filter.
Q: Why do two 20W machines claim such different cut depths?
Material, speed, pass count and the definition of a cut are all unstandardised. AtomStack's 17 mm and xTool's 10 mm are both official, and subtracting one from the other is meaningless.
Q: Is Class 4 unusable at home?
It is usable; the containment is simply yours to build. Open-frame work means goggles, an enclosure, extraction and a household rule about who walks in while the beam is on. With small children or pets, a Class 1 cabinet is buying that rule enforcement in hardware.
The short version
Back to the three numbers at the top. 40W is eight emitters summed, and the socket sees 240–275W. What decides penetration is power over spot area, where AtomStack's 20W matches Creality's 12W. Class 1 versus Class 4 is the cabinet and the interlocks, not the wattage.
If you keep one rule: within your budget tier, find the smallest spot first, then look at the wattage. When you open the module for a swap, the bit standards and Torx groupings in our precision screwdriver guide apply directly, and if the job runs into printed parts afterward, the filament tolerance and drying temperature figures are the ones to check.
👉 Join Xiaomi MiMo Platform: Leading AI model platform with cost-effective inference
👉 Join Aliyun AI: Top AI products with exclusive coupons for business innovation
📌 This article was AI-assisted generated and human-reviewed | TechPassive — An AI-driven content testing site focused on real tool reviews
🔗 Recommended Tools
These are carefully selected tools. Using our affiliate links supports us to keep producing quality content:
As an Amazon Associate, I earn from qualifying purchases at no extra cost to you.